How To Clean The Spray Gun Properly?

Correct spray gun cleaning

1. When you clean the paint gun, leave the cap on it. This will make it impossible to remove the paint from the inside of the cap and on the tip of the fluid-these things accumulate time!

Do this: Remove the cap and use a flowing brush to remove the paint from the inside of the cap and the tip of the fluid-pay attention to the small holes in the "horns" of the air cap-if they are clogged, your spray mode is TOAST!

2. When you are cleaning the gun, don't worry about the liquid entering the air passage.

When the water-based cleaning fluid is repeatedly dried in the air channel, it will cause corrosion, and the flakes that will eventually fall off will directly enter your paint job...

Do this: During the cleaning process, always quickly disconnect the compressed air to the base of the gun. This "seals-out" the liquid, and when you trigger the spray gun during the cleaning process, it can help flush the inside of the spray gun, where the fluid and air gather together to atomize the paint.

3. Before cleaning the paint gun, clean it with a solvent. Using any kind of solvent (thinner, ammonia, rain, degreaser, etc.) will make the waterborne paint gun more viscous. When you clean the gun with waterborne cleaning fluid, it will be more difficult to get out of the gap in the liquid channel.

You can do this: After pulling out the muzzle, pour the remaining paint in the gun into the waste bucket. Then pre-rinse the paint gun with water, and then pour the paint gun into the waste barrel too! Be sure to "trigger" the gun and let some of the rinse come out of the fluid tip.

4. Don't worry, if some paint remains in the liquid channel after cleaning-the paint that passes through the next layer will wash it away. Waterborne paint is completely different! When it dries, it hardens and piles up, and it is almost impossible to disperse it with waterborne cleaning fluids.

Do this: If you see paint on the cup connector area or fluid tip after cleaning, please continue cleaning! If the paint still does not come off, tear off the gun and use acetone to do a detailed cleaning of the paint gun manufacturer’s recommendations.

5. When you finish cleaning the gun, be sure to "chase" the clean gun with a little solvent, and leave a little thinner in the gun to keep the seal, the o-ring and the remaining paint soft. This is a habit that many of us have developed when using solvent paint guns, and the opposite is true for waterborne guns. Clean and dry are always best.

Do this: hang up when you are sure that the paint gun is clean and dry (internal and external)-it is ready for next use.

We are spray gun suppliers. If you are interested in our products, please feel free to contact us.

How To Choose The Right Detailing Brush?

1. The bristles need to be medium. If hard, they will damage the car painting.

2. Pull the bristles of the brush by hand, if they fall off easily, the quality will be poor.

3. When the brush is used with a chemical liquid, the bad brush is easy to fall off after being used with the liquid.

4. High-quality brushes look more smooth and density.

A true artist always needs to select high-quality brushes, right? That's why we have developed a complete selection of advanced brushes over the years. Brushes are important tools, and they can not only reach areas that other parts of your car care package cannot. However, they can even better master the professional-level skills that are often forgotten. Here are some professional tips to help you create a masterpiece.

Fuel caps and flaps

What is the first thing a competent detailer needs to do before cleaning? Of course they will open the fuel cap. Admittedly, this is a trivial matter, but many people have overlooked it. Inside the flap, and around the flap, is one of the biggest dirt traps on any car-this often becomes obvious when washing with a high-pressure washer, because clean water will wash away grit, dirt, and fuel deposits...then they will slip off the paint you just washed. Fortunately, the solution is simple.

Internal door

Removing dirt and debris trapped in door frames and door frames is what most people do during cleaning and maintenance, but you will be surprised to find how many people forget to clean the inside of the door.

Weather strips

Thorough decontamination of weather strips and window decorations is not only for protection-not to mention preventing common scratches that may occur on the window glass-but also to make your decoration beautiful and flawless. Perhaps even more. Over time, the rubber weather strip will degrade, not only will it lose the effective seal between the door and the glass, but it will also become a breeding ground for rough grit and road dirt. In the cleaning phase, proper use of brushes to agitate and remove contaminants can limit the decomposition of rubber and reduce the risk of external glass damage when opening and closing windows.

Engine bay

Even the dirty bay of the engine--especially in the more complicated areas off, in the slam panel and headlights, and even the bottom of the hat--can bring back to life except for the Auto Detailing Brushes Wholesale. In all these difficult areas, the key to maximizing the cleaning power of the solution is stirring.

Interiors

We all know that in dry conditions, bristles are very suitable for dust removal in hard-to-reach and most complex areas such as buttons, heating vents, and steering columns. It is worth remembering that many vehicles used daily can be as dirty as their exterior, even if it is not immediately obvious to the eyes. Under normal circumstances, you will find that plastics and trim loaded with nasties, such as dead skin, natural body oils, bacteria and viruses, and usually dirt and a small amount of cosmetics. The only effective way to remove these is a thorough deep clean.

Car Beauty Step Ladder car detailing car beauty accessory

 Car Beauty Step Ladder    car detailing    car beauty accessory      car beauty      car cleaning tools

 

Product Description

This product adopts a stepped design, easy to take, and flexibly used according to the height of the vehicle. Construction personnel can clearly see the hard-to-reach places on the roof.

 

1. Non-slip foot pads.

Each leg is equipped with anti-skid pads.

 

2. Safety and stable.

The use of high-quality thickened environmentally friendly materials, strong bearing capacity, uniform force, waterproof and anti-corrosion.

 

3. Bumpy design.

This product's intimate anti-skid design ensures the safety of construction personnel.

 

4. Trapezoidal design.

The double-layer ladder design of this product is convenient and stable up and down.

 

5. Product information.

Name: Car beauty step ladder.

Material: ABS.

Size: 610mm*530mm*460mm.

Advantage: Safe and non-slip, durable and widely used.

 

We can supply high quality professional car wash brush, at the same time we can provide experience on how to better clean the car body. Choose us, you can be get most careful and thoughtful service!

 

Our website: www.chinacarcleaningtools.com

 

https://www.chinacarcleaningtools.com/product-car-beauty-step-ladder.html

 

Water Vapor Mixing Foam Spray Gun Water vapor mixing foam gun

 Water Vapor Mixing Foam Spray Gun   Water vapor mixing foam gun    interior detailing brush wholesale

 

Product Description

This product is specially used for water vapor mixing drum, which can improve the inconvenience caused by the foam gun filling the foam frequently and improve the working efficiency.

 

1. Adjustable switch.

Adjustable switch design can adjust the output size according to actual needs, improve efficiency.

 

2. Rust-proof joint.

The interface is treated by a special process to prevent corrosion and rust.

 

3. Double spearhead.

Equipped with two different types of gun head, choose according to the actual situation, flexible use, wide range.

 

4. Handle design.

Aluminum alloy handle, his design follows ergonomics, comfortable grip, flexible use, strong and durable.

 

5. Product information:

Name: Water vapor mixing foam gun

Material: PP Plastic and Aluminum alloy

Air pressure: 6.2BAR/90 PSI

Length: 30cm.

Caliber: 6*10 mm.

 

As a professional auto brush supplier, we supply top-quality fine-washing beauty products at home and abroad. We can help you solve all kinds of problems and stains you encounter when cleaning the car body.

 

If you want to know more about car cleaning tools, please click here to visit our website.

 

https://www.chinacarcleaningtools.com/product-water-vapor-mixing-foam-spray-gun1.html