What Should Be Paid Attention to in Car Cleaning?

 The other is car wash technology. Car washing refers to the cleaning inside and outside the car, which is more detailed and cleaner than traditional car washing. Car wash is a problem that every car owner or driver often faces. Car wash shops have gradually become a hot investment project in many large and medium-sized cities.

Car wash is one of the main technical projects in the car wash industry because of its good service, multiple steps, complete equipment, and high cost.

There are many differences between car fine washing and traditional car washing. First of all, car fine washing uses treated soft water instead of ordinary tap water. Even the flannel for wiping the car body is used separately for different body parts.

Long Handle Brushes

Precautions for car cleaning

Cars should be washed and waxed frequently. After the road salting season is over, the underside of the car should be thoroughly cleaned, and the following points should be paid attention to when cleaning the car:

⑴The longer the salt, dust, insects, bird droppings and other debris stick to the car, the greater the destructive effect on the car, and it should be cleaned in time.

⑵ When washing the car with water, be careful not to spray water into the keyhole.

⑶ If the car is sent to the automatic cleaning equipment for cleaning, the car with roof antenna does not need to be removed.

⑷The body is stained with asphalt, oil stains, industrial dust or insects. If it takes too long, they will damage the paint. Use asphalt remover, insect remover, etc. to remove stains.

⑸ When cleaning the paint surface of the car body, do not use brushes, coarse cloths, etc., to avoid leaving scratch marks.

⑹When cleaning, spray with dispersed water stream to infiltrate the hard dust and mud and be impacted, and then use a sponge to scrub from top to bottom. Finally wipe off the water stains with deerskin.

⑺ When cleaning the engine room, be careful not to splash water on electrical system parts such as distributors and ignition coils. Otherwise, it will be difficult for the engine to start. In case of water splashing on the electrical parts, wipe the water with a dry cloth or blow it with compressed air, and remove the moisture in the distributor cover.

⑻After washing the car or driving in deep water, the braking effect may be reduced due to the soaking of the brake parts. You should lightly step on the brake to judge the braking effect. If the brake is not normal, you should run at low speed while stepping on the brake to dry the brake.

We are the Detail Brushes supplier. Our company provides a series of Long Handle Brushes for car cleaning. If you are interested in our products, please feel free to contact us.

How to Wash the Car Correctly?

 There are more and more people who own cars, but many car owners have not formed a correct understanding of car washing. Most people wait for the car to be too dirty to wash before going to the car; some people even think that washing the car is enough to wait for it to rain, so you don't need to do it yourself.

In fact, car washing is one of the most basic maintenance measures. Car washing is to remove the sludge on the car body, the pollutants in the air, and the stains such as bird droppings and corpses, and to avoid the corrosion and oxidation of these stains on the paint. Take rainwater as an example. Industrial emissions and automobile exhaust gas cause rainwater to acidify, which can cause great corrosion to car paint. Therefore, the best way to protect the paint is to develop the habit of car washing.

For the work of car washing, you can do it yourself if you have time. Next, the tire cleaning brush exporter will share with you some independent car washing methods.

First, let’s take a look at the weapons and equipment to be prepared:

1. Professional car wash liquid. The choice of car wash is the most important link, and neutral car wash should be selected. Acidic or alkaline cleaners are corrosive to car paint. At present, the more popular car wash wax (waxed car wash liquid) is a good choice.

2. Cleaning Spray Gun. The use of flush guns can greatly improve efficiency and reduce physical output.

3. Two car wash buckets with a filter at the bottom. The purpose of the filter is to allow the sediment to be deposited and prevent the wiped sediment from being carried back to the body.

4. Special car wash gloves. The protection of the opponent, not much to say.

5. Multifunctional detail brush. Clean difficult and dead spots.

6. Fine fiber water-receiving towel.

 Cleaning Spray Gun

Then, enter the steps of scientific quick washing:

1. Look for a cool place. In order to avoid leaving water marks and spots after washing the car, and at the same time to prevent thermal expansion and contraction from causing damage to the paint, the car washing location should be selected to avoid the hot sun.

2. Wait for the body, front cover and engine to cool down. Uncooled car paint is prone to cracking due to sharp cold shrinkage when exposed to cold water. The same principle will also cause damage to the engine, so I must wait until the body, front cover and engine have cooled down before washing the car.

3.One bucket is filled with clean water, and the other bucket is equipped with car wash liquid.

4. Refer to the car wash instructions and dilute the car wash in proportion.

5. Water gun flushing. Wash the car body from top to bottom. In addition, the pressure of the water gun should not be too high, because the sand and sand on the car body impacted by high pressure will wear the paint.

6. Put on the car wash gloves and dip the matched car wash liquid, and scrub the car body from top to bottom. Be careful not to use too much force during the scrubbing process. If you find that there is still sand, you should immediately rinse with water and then continue scrubbing to prevent scratching the body.

7. Use detail soft brush to handle the corners of the door frame glass.

8. Flush for the second time.

9. Collect water. After the car body is washed, it is particularly important to collect water in order to prevent water marks. Collect water in different areas, and different towels do not serve different areas. Generally, four doors and front and rear covers, glass and roof, and others in the order of priority.

Cleaning and Daily Maintenance of the Spray Gun After Use

 1. Cleaning of the spray gun

After use, the cleaning spray gun and its accessories should be cleaned immediately. Maintenance and cleaning of the medallion is the main reason for the failure of the spray gun.

When cleaning the suction feed spray gun, first remove the paint tank), and flow the suction tube into the cup. Then loosen the air cap 2-3 turns, block the air cap with a folded rag, and then pull the trigger. This allows the paint in the spray gun to flow back into the paint tank.

Note: The air pressure used should be low. When the paint tank is still installed on the gun, do not perform the above operations, otherwise the paint will splash out of the tank.

Tighten the air cap again and pour the paint in the paint tank back into the original large tank. Clean the inside of the cup and the lid with solvent and a thin brush) Wipe off the residue with a cloth soaked in solvent. Then pour a little clean detergent into the cup, squeeze the trigger, spray the detergent, and clean the feeding pipe.

Then remove the air cap, soak it in thinner or solvent, and use a soft brush like a round toothbrush or a straw broom to clean the clogged holes. Remember, never use things like iron wire or nails to clean these small holes, because these small holes are all drilled. Clean the nozzle with a spray gun brush and solvent. Wipe the outside of the gun body with a cloth soaked in thinner, taking care to wipe off all traces of paint.

At present, automatic spray gun cleaning machines have been used in some areas and units, combined with manual hand washing to clean spray guns, and the cleaning effect is very good. Put the spraying equipment in the large barrel of the spray gun cleaning and recycling machine, cover the lid, and then turn on the pneumatic pump to rotate the cleaning liquid in the cleaning barrel. In less than 1 minute, the equipment can clean all parts for use. Compared with the traditional manual cleaning method, the automatic cleaning solution can save 10 minutes of the time of changing the paint. This cleaning device increases the safety of the painter because the skin is no longer exposed to those solvents with drying effect. In the design of the system, there is a screw plug at the bottom, which can easily drain the waste liquid.

In operations such as cleaning the spray gun, a large amount of solvent will remain. If it is poured directly, it is wasteful and not good for environmental protection. The solvent recovery machine uses high-temperature distillation to recover the dirty solvent and obtain clean solvent, which saves a lot of solvent and protects the environment.

Cleaning Spray Gun

The auto brush supplier reminds you: If the spray gun is not cleaned immediately after use, the nozzle will be partially or completely blocked, causing the spray spray from the spray gun to split (spray out dry paint fragments) or the spray shape is wrong . This is especially true for enamels with additives. Because if it is not cleaned immediately after use, the enamel paint will harden inside the spray gun.

Second, the maintenance of cleaning gun

It is best to lubricate the spray gun after working every day and lubricate the parts with a light machine. Due to normal wear and aging, seals, springs, needle valves and nozzles must be replaced regularly. The replacement should be carried out according to the manufacturer's instructions. Excessive oil will flow into the paint and oil passages, causing spraying defects. Therefore, you must be very careful when lubricating. The mixing of oil and paint will reduce the quality of spraying.